FlowMax Rv Water Pump 12V Flow-MaX 3.3 GPM Self-Priming 50PSI Replaces Shurflo

FlowMax Rv Water Pump 12V Flow-MaX 3.3 GPM Self-Priming 50PSI Replaces Shurflo
item image
 Buy Now
Facebook Twitter Pinterest

Price: 6895 USD

FlowMax Rv Water Pump 12V Flow-MaX 3.3 GPM Self-Priming 50PSI Replaces Shurflo

FlowMax Rv Water Pump 12V Flow-MaX 3.3 GPM Self-Priming 50PSI Replaces Shurflo

Lippert Components RV Fresh Water – LC689052

  • Water Pump
  • Lippert Components

Motorized, self-priming pump creates a consistent flow of fresh water to your RV or camper. Works as a direct replacement for a 12-volt pump. The quiet pump has a check valve to prevent backflow and a thermal breaker to prevent overheating.

Features:

  • Motorized water pump provides a consistent flow of fresh water to your RV or camper
    • Can be used as a direct replacement for any OEM RV or marine pump
  • Self-priming design eliminates air binding by removing air from the pipeline
    • Unit is capable of up to 6′ vertical prime and 30′ horizontal prime
  • Heavy-duty, corrosion-resistant motor has ball bearings for a long life
    • Provides quiet, disturbance-free operation
    • Can run dry without causing damage
  • Integrated thermal breaker protects the motor from overheating
    • Breaker automatically resets when temperature drops
  • Internal check valve prevents backflow contamination of your clean water supply
  • Included strainer stops bugs and debris from entering the pump
  • Feet are flexible to reduce excessive vibration and noise
  • Enclosed housing with sealed switches blocks moisture from getting in
    • Electrocoating finish resists the effects of rain and other elements
  • Bolt-on installation in any position
    • Hardware not included
  • 1/2″ Diameter hose fitting at inlet and outlet ports
    • Features a tapered seal for a watertight connection
    • Includes 2 swivel, high-pressure fittings
  • 15 Amp switch and a 10 amp fuse (not included) are required
  • Freeze and thaw tested up to 5 cycles of 2 hours
  • NSF and CSA certified

Specs:

  • Overall dimensions: 8″ long x 5-1/4″ wide x 5″ tall
  • Mounting base dimensions: 3-3/4″ long x 4-1/4″ wide
  • Voltage: 12 volts DC
  • Maximum power draw: 8 amps
  • Flow: 3.3 gallons per minute
  • Pressure setting: 45 psi
  • Runtime: 5 minutes on/10 minutes off
  • Maximum water temperature: 140 degrees F (60 degrees C)
  • 2-Year limited warranty

Notes:

  • Designed for intermittent use only – continuous running under higher pressures may reduce pump life.
  • Pump should not be used for running a Reverse-Osmosis (RO) Filtration System.

Self-Priming Water Pump

This motorized pump can be used as a direct replacement for any OEM RV or marine pump and lets you supply a smooth, consistent flow to the fresh water system in your RV, camper, or boat. The diaphragm-style pump has a self-priming design. The sealed, flexible diaphragm creates a vacuum that draws in the water, allowing the pump to self-prime. This design eliminates air pockets in the pipeline – also known as air binding – for a steady, uninterrupted stream of water to your faucet or other fresh water source. It has the ability to prime up to 6′ vertically and 30′ horizontally. The pump also features an internal check valve that prevents backflow contamination of your clean water supply.

The pump has been thoroughly freeze and thaw tested for up to 5 two-hour cycles, and it was tested with a higher pressure at shutoff than other water pumps.

Heavy-Duty Motor

The heavy-duty motor operates quietly without any disturbances and features ball bearings that enable it to have a long life. It doesn’t have a rotating seal that will burn up, allowing it the ability to run dry without causing any damage.

The motor also has an integrated thermal breaker that interrupts operation when the motor becomes too hot in order to protect it from overheating. When the temperature of the motor drops, the breaker automatically resets.

Water-Resistant Design

This enclosed, water-resistant pump has sealed switches that keep moisture from getting in. The electrocoating finish withstands the effects of rain, snow, and other elements, preventing rust and ensuring long-lasting durability.

Installation

This water pump can be bolted down in multiple locations and positions. It can be installed above, below, or at the same level as the water tank, as long as the location is dry and easily accessible for maintenance. Mounting hardware is not included.

Once the pump is bolted down, insert the strainer on the inlet side. This strainer prevents bugs and debris from entering the pump. Then with the included swivel fittings, attach high-pressure hoses to the strainer and the outlet port for a tapered, watertight seal.

Finally, make your wire connections. The black wire is your live (or hotwire), the white wire is your neutral, and the green and yellow wire is your ground. Please note that a 15 amp switch and a 10 amp fuse (not included) are required.

Payment

Shipping

Returns

We accept payment by any of the following methods:

PayPal

Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!

We offer FREE shipping on all orders!

Your order will be dispatched within 2 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).

In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.

If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.

You can return a product for up to 14 days from the date you purchased it.

Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.

Lippert Components RV Fresh Water – LC689052 —Water Pump —Lippert Components Motorized, self-priming pump creates a consistent flow of fresh water to your RV or camper. Works as a direct replacement for a 12-volt pump. The quiet pump has a check valve to prevent backflow and a thermal breaker to prevent overheating. Features: —Motorized water pump provides a consistent flow of fresh water to your RV or camper ——Can be used as a direct replacement for any OEM RV or marine pump —Self-priming design eliminates air binding by removing air from the pipeline ——Unit is capable of up to 6′ vertical prime and 30′ horizontal prime —Heavy-duty, corrosion-resistant motor has ball bearings for a long life ——Provides quiet, disturbance-free operation ——Can run dry without causing damage —Integrated thermal breaker protects the motor from overheating ——Breaker automatically resets when temperature drops —Internal check valve prevents backflow contamination of your clean water supply —Included strainer stops bugs and debris from entering the pump —Feet are flexible to reduce excessive vibration and noise —Enclosed housing with sealed switches blocks moisture from getting in ——Electrocoating finish resists the effects of rain and other elements —Bolt-on installation in any position ——Hardware not included —1/2″ Diameter hose fitting at inlet and outlet ports ——Features a tapered seal for a watertight connection ——Includes 2 swivel, high-pressure fittings —3-Wire configuration ——Black for live (hotwire) ——White for neutral ——Green and yellow for ground —15 Amp switch and a 10 amp fuse (not included) are required —Freeze and thaw tested up to 5 cycles of 2 hours —NSF and CSA certified Specs: —Overall dimensions: 8″ long x 5-1/4″ wide x 5″ tall —Mounting base dimensions: 3-3/4″ long x 4-1/4″ wide —Voltage: 12 volts DC —Maximum power draw: 8 amps —Flow: 3.3 gallons per minute —Pressure setting: 45 psi —Runtime: 5 minutes on/10 minutes off —Maximum water temperature: 140 degrees F (60 degrees C) —2-Year limited warranty Notes: —Designed for intermittent use only – continuous running under higher pressures may reduce pump life. —Pump should not be used for running a Reverse-Osmosis (RO) Filtration System. Self-Priming Water Pump This motorized pump can be used as a direct replacement for any OEM RV or marine pump and lets you supply a smooth, consistent flow to the fresh water system in your RV, camper, or boat. The diaphragm-style pump has a self-priming design. The sealed, flexible diaphragm creates a vacuum that draws in the water, allowing the pump to self-prime. This design eliminates air pockets in the pipeline – also known as air binding – for a steady, uninterrupted stream of water to your faucet or other fresh water source. It has the ability to prime up to 6′ vertically and 30′ horizontally. The pump also features an internal check valve that prevents backflow contamination of your clean water supply. The pump has been thoroughly freeze and thaw tested for up to 5 two-hour cycles, and it was tested with a higher pressure at shutoff than other water pumps. Heavy-Duty Motor The heavy-duty motor operates quietly without any disturbances and features ball bearings that enable it to have a long life. It doesn’t have a rotating seal that will burn up, allowing it the ability to run dry without causing any damage. The motor also has an integrated thermal breaker that interrupts operation when the motor becomes too hot in order to protect it from overheating. When the temperature of the motor drops, the breaker automatically resets. Water-Resistant Design This enclosed, water-resistant pump has sealed switches that keep moisture from getting in. The electrocoating finish withstands the effects of rain, snow, and other elements, preventing rust and ensuring long-lasting durability. Installation This water pump can be bolted down in multiple locations and positions. It can be installed above, below, or at the same level as the water tank, as long as the location is dry and easily accessible for maintenance. Mounting hardware is not included. Once the pump is bolted down, insert the strainer on the inlet side. This strainer prevents bugs and debris from entering the pump. Then with the included swivel fittings, attach high-pressure hoses to the strainer and the outlet port for a tapered, watertight seal. Finally, make your wire connections. The black wire is your live (or hotwire), the white wire is your neutral, and the green and yellow wire is your ground. Please note that a 15 amp switch and a 10 amp fuse (not included) are required.

FlowMax Rv Water Pump 12V Flow-MaX 3.3 GPM Self-Priming 50PSI Replaces Shurflo

Lippert Components RV Fresh Water – LC689052

  • Water Pump
  • Lippert Components

Motorized, self-priming pump creates a consistent flow of fresh water to your RV or camper. Works as a direct replacement for a 12-volt pump. The quiet pump has a check valve to prevent backflow and a thermal breaker to prevent overheating.

Features:

  • Motorized water pump provides a consistent flow of fresh water to your RV or camper
    • Can be used as a direct replacement for any OEM RV or marine pump
  • Self-priming design eliminates air binding by removing air from the pipeline
    • Unit is capable of up to 6′ vertical prime and 30′ horizontal prime
  • Heavy-duty, corrosion-resistant motor has ball bearings for a long life
    • Provides quiet, disturbance-free operation
    • Can run dry without causing damage
  • Integrated thermal breaker protects the motor from overheating
    • Breaker automatically resets when temperature drops
  • Internal check valve prevents backflow contamination of your clean water supply
  • Included strainer stops bugs and debris from entering the pump
  • Feet are flexible to reduce excessive vibration and noise
  • Enclosed housing with sealed switches blocks moisture from getting in
    • Electrocoating finish resists the effects of rain and other elements
  • Bolt-on installation in any position
    • Hardware not included
  • 1/2″ Diameter hose fitting at inlet and outlet ports
    • Features a tapered seal for a watertight connection
    • Includes 2 swivel, high-pressure fittings
  • 3-Wire configuration
    • Black for live (hotwire)
    • White for neutral
    • Green and yellow for ground
  • 15 Amp switch and a 10 amp fuse (not included) are required
  • Freeze and thaw tested up to 5 cycles of 2 hours
  • NSF and CSA certified

Specs:

  • Overall dimensions: 8″ long x 5-1/4″ wide x 5″ tall
  • Mounting base dimensions: 3-3/4″ long x 4-1/4″ wide
  • Voltage: 12 volts DC
  • Maximum power draw: 8 amps
  • Flow: 3.3 gallons per minute
  • Pressure setting: 45 psi
  • Runtime: 5 minutes on/10 minutes off
  • Maximum water temperature: 140 degrees F (60 degrees C)
  • 2-Year limited warranty

Notes:

  • Designed for intermittent use only – continuous running under higher pressures may reduce pump life.
  • Pump should not be used for running a Reverse-Osmosis (RO) Filtration System.

Self-Priming Water Pump

This motorized pump can be used as a direct replacement for any OEM RV or marine pump and lets you supply a smooth, consistent flow to the fresh water system in your RV, camper, or boat. The diaphragm-style pump has a self-priming design. The sealed, flexible diaphragm creates a vacuum that draws in the water, allowing the pump to self-prime. This design eliminates air pockets in the pipeline – also known as air binding – for a steady, uninterrupted stream of water to your faucet or other fresh water source. It has the ability to prime up to 6′ vertically and 30′ horizontally. The pump also features an internal check valve that prevents backflow contamination of your clean water supply.

The pump has been thoroughly freeze and thaw tested for up to 5 two-hour cycles, and it was tested with a higher pressure at shutoff than other water pumps.

Heavy-Duty Motor

The heavy-duty motor operates quietly without any disturbances and features ball bearings that enable it to have a long life. It doesn’t have a rotating seal that will burn up, allowing it the ability to run dry without causing any damage.

The motor also has an integrated thermal breaker that interrupts operation when the motor becomes too hot in order to protect it from overheating. When the temperature of the motor drops, the breaker automatically resets.

Water-Resistant Design

This enclosed, water-resistant pump has sealed switches that keep moisture from getting in. The electrocoating finish withstands the effects of rain, snow, and other elements, preventing rust and ensuring long-lasting durability.

Installation

This water pump can be bolted down in multiple locations and positions. It can be installed above, below, or at the same level as the water tank, as long as the location is dry and easily accessible for maintenance. Mounting hardware is not included.

Once the pump is bolted down, insert the strainer on the inlet side. This strainer prevents bugs and debris from entering the pump. Then with the included swivel fittings, attach high-pressure hoses to the strainer and the outlet port for a tapered, watertight seal.

Finally, make your wire connections. The black wire is your live (or hotwire), the white wire is your neutral, and the green and yellow wire is your ground. Please note that a 15 amp switch and a 10 amp fuse (not included) are required.

We accept payment by any of the following methods:

PayPal

Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!

We offer FREE shipping on all orders!

Your order will be dispatched within 2 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).

In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.

If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.

You can return a product for up to 14 days from the date you purchased it.

Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.

You May Also Like